CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018
6
Fuel tank (Eos)
Safety precautions when working on fuel supply system
⇒ page 278 .
Comply with rules for cleanliness ⇒ page 280 .
Assembly overview - fuel tank (engine codes CBFA, CCTA,
CCTB) ⇒ page 316 .
Drain fuel tank ⇒ page 318 .
Removing and installing fuel tank ⇒ page 322 .
6.1
Assembly overview - fuel tank (engine codes CAWA, CAWB, CCZA, CCZB)
1 - Securing bolt
2 - Cap
❑ Renew if damaged
3 - Earth connection
❑ Ensure firm seating
4 - 10 Nm
5 - Cable bracket
6 - 25 Nm
❑ Renew
❑ To secure the securing
straps for the fuel tank,
only bolts with loose
washers must be used.
If different bolts are
used, the securing
straps might twist during
tightening.
7 - Fuel
❑ When removing, sup‐
port using engine and
gearbox jack - V.A.G
1383 A- .
❑ Removing and installing
⇒ page 322
8 - Clamping washer
9 - Exhaust system retainer
10 - Securing strap
❑ Observe installation po‐
sition
❑ To secure the securing
straps for the fuel tank,
only bolts with loose
washers must be used. If different bolts are used, the securing straps might twist during tightening.
11 - Heat shield
12 - Supply line
❑ To fuel rail
❑ Ensure firm seating
314
Rep. gr.20 - Fuel supply system
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018
13 - Fuel filter
❑ Fitting position ⇒ page 316
❑ Arrow points in direction of flow.
14 - Breather line
❑ Clipped onto side of fuel tank.
❑ Ensure firm seating
15 - Seal
❑ Renew
❑ When installing, fit dry in fuel tank opening.
❑ Moisten with fuel only when installing flange.
16 - Fuel delivery unit
❑ Removing and installing ⇒ page 346
❑ Checking fuel pump ⇒ page 350 .
❑ With fuel gauge sender - G-
❑ Removing and installing fuel gauge sender - G- ⇒ page 349
❑ Clean strainer if soiled
17 - Locking ring 110 Nm
❑ Ensure firm seating
❑ Remove and install using wrench - T10202- .
18 - Supply line
❑ black
❑ Clipped onto side of fuel tank.
❑ Ensure firm seating
19 - Return line
❑ blue
❑ Clipped onto side of fuel tank.
❑ Ensure firm seating
20 - Tank flap unit
❑ With rubber cup.
❑ Removing and installing ⇒ General body repairs, exterior; Rep. gr. 55 ; Tank flap unit; Removing and
installing fuel tank flap unit .
Installation position of fuel delivery unit
•
Tab -2- on flange must be between lugs -1- and -3- on fuel
tank.
•
-Arrow- points in direction of travel.
6. Fuel tank (Eos)
315
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018
Location of fuel filter
Pin -2- on filter housing must engage in notch of guide -1- on filter
bracket.
6.2
Assembly overview - fuel tank (engine codes CBFA, CCTA, CCTB)
1 - Securing bolt
2 - Earth connection
❑ Ensure firm seating
3 - 11 Nm
4 - Rivet
5 - Protective plate
❑ Riveted as standard to
bottom clamp
❑ When replacing fuel
tank, hold protective
plate against filler pipe
and rivet to clamp
6 - Cable bracket
❑ Clipped onto protective
plate
7 - 25 Nm
❑ Renew
❑ To secure the securing
straps for the fuel tank,
only bolts with loose
washers must be used.
If different bolts are
used, the securing
straps might twist during
tightening.
8 - Fuel
❑ When removing, sup‐
port using engine and
gearbox jack - V.A.G
1383 A- .
❑ Removing and installing
⇒ page 323
9 - Clamping washer
10 - Exhaust system retainer
11 - Securing strap
❑ Observe installation position
12 - Heat shield
13 - Supply line
❑ To fuel rail
316
Rep. gr.20 - Fuel supply system
2024 VW Passat Owner's Manual
VW Passat B7 Service & Repair Manual
VW Passat B6 Service & Repair Manual
