Download
Table of Contents > Assembly mountings > Adjusting assembly mounting (Tiguan)

VW Passat B6 Service Manual ➜ Adjusting assembly mounting (Tiguan)

CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...  
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018  
Vehicles with automatic gearbox  
– Renew assembly mounting bolts -arrows- on gearbox side one  
after the other (if not already carried out during engine instal‐  
lation) and screw in hand-tight.  
All:  
– Slacken bolts on left and right-hand support arms by about two  
turns each.  
– Adjust assembly mounting and screw in securing bolts hand-  
tight.  
There must be a distance -a- of at least 10 mm between engine  
support and longitudinal member (right side).  
The side surface of the engine support -2- should be located  
parallel to the support arm -1-.  
Vehicles with manual gearbox:  
Ensure that edges of support arm (on gearbox side) -1- and  
gearbox mounting -2- are parallel.  
Dimension -x- must be identical on both sides of mounting.  
Vehicles with automatic gearbox:  
Ensure that edges of support arm (on gearbox side) -A- and  
gearbox mounting -B- are parallel.  
Dimension -x- must be identical on both sides of mounting.  
All:  
– Tighten bolts for assembly mounting to required specified tor‐  
que ⇒ page 21 .  
Continue installation in reverse order of removal.  
2.6  
Adjusting assembly mounting (Tiguan)  
Special tools and workshop equipment required  
32  
Rep. gr.10 - Removing and installing engine  
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...  
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018  
♦ Support - 10-222A-  
♦ Shackle - 10-222A/12-  
♦ Adapter - 10-222A/16-  
♦ Adapter - 10-222A/18-  
♦ Adapter - 10-222A/22-  
♦ Adapter - 10-222A/19-  
♦ Square tube - T40091/1-  
♦ Swivel joint - T40091/3-  
Adjusting  
Proceed as follows:  
– Remove engine cover panel ⇒ page 141 .  
– Remove air filter ⇒ page 467 .  
Caution  
Risk of irreparable damage to electronic components when  
disconnecting battery.  
♦ Observe the necessary measures when disconnecting the  
battery.  
2. Assembly mountings  
33  
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...  
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018  
– Disconnect earth cable -arrow- from battery when ignition is  
switched off.  
– Remove battery ⇒ Rep. gr. 27 .  
– Remove battery tray -arrows-.  
– Fit support bracket - 10 - 222 A- as shown. The rear spindle is  
not required. Attach hooks to support eyes on engine and  
support engine and gearbox.  
– Support engine with gearbox, but do not raise.  
34  
Rep. gr.10 - Removing and installing engine  
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...  
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018  
– Renew assembly mounting bolts -arrows- on engine side one  
after the other (if not already carried out during engine instal‐  
lation) and screw in hand-tight.  
Vehicles with manual gearbox:  
– Renew assembly mounting bolts -arrows- on gearbox side one  
after the other (if not already carried out during engine instal‐  
lation) and screw in hand-tight.  
Vehicles with automatic gearbox:  
– Renew assembly mounting bolts -arrows- in succession (if not  
already carried out on installing engine) and screw in hand-  
tight.  
All:  
– Slacken bolts on left and right-hand support arms by about two  
turns each.  
– Adjust assembly mounting and screw in securing bolts hand-  
tight.  
Assembly mounting on engine side:  
There must be a distance -a- of at least 10 mm between engine  
support and longitudinal member (right side).  
The side surface of the engine support -2- should be located  
parallel to the support arm -1-.  
2. Assembly mountings  
35  
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...  
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018  
Assembly mounting on gearbox side:  
Ensure that edges of support arm (on gearbox side) -1- and  
gearbox mounting -2- are parallel.  
Dimension -x- must be identical on both sides of mounting.  
– Tighten bolts for assembly mounting to required specified tor‐  
que ⇒ page 23 .  
Continue installation in reverse order of removal.  
36  
Rep. gr.10 - Removing and installing engine  

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car VW Passat you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!