Download
Table of Contents > Descriptions of work > Warning stickers, Passat GTE: checking

VW Passat B8 Service Manual ➜ Warning stickers, Passat GTE: checking

Passat 2015 ➤, Passat 2019 ➤, Passat Variant 2015 ➤, Passat Variant 2019 ➤  
Maintenance - Edition 11.2020  
– To rectify dents, slide bellows upwards, reach inside the  
bellows with your hand and press out the dents.  
– Check that bellows are properly engaged in axial bearing:  
♦ Correct position: bellows can be turned around rotational  
axis while seated in axial bearing.  
♦ Otherwise pull bellows all-round out of axial bearing by one  
notch.  
♦ After that, the bellows should be able to be turned around  
rotational axis.  
4.65  
Clock and date: setting  
Setting time and date in Infotainment system  
– Switch on ignition.  
– Switch on Infotainment system.  
– Press Infotainment button CAR.  
– Press Setup function button.  
– Press Time and date function button.  
– Select function button Time and set current time.  
– Select function button Date set current date.  
4.66  
Underbody: inspecting for damage to  
underbody sealant, underbody panels,  
routing of lines, plugs  
NOTICE  
During inspection, also check floor pan, wheel housings  
and sills.  
♦ Always ensure that all lines are secured in their mountings,  
that all plugs are available and that there is no visible  
damage on the underbody.  
♦ Faults found must always be rectified (repair measure).  
This inhibits corrosion and rusting through.  
4.67  
Warning stickers, Passat GTE: check‐  
ing  
There are warning stickers on all high-voltage components.  
When performing maintenance work, make sure that these  
warning stickers are not soiled or damaged and are present  
on all high-voltage components.  
190  
4. Descriptions of work  
Passat 2015 ➤, Passat 2019 ➤, Passat Variant 2015 ➤, Passat Variant 2019 ➤  
Maintenance - Edition 11.2020  
Note  
During oil change service or inspection, only warning stick‐  
ers that are attached in visible areas are checked.  
Missing warning stickers on high-voltage components must  
be renewed.  
– Check warning sticker ⇒ 4-cyl. direct injection (1.4 l engine,  
4V, EA 211, turbocharger, hybrid); Rep. gr. 93; Warning  
sticker; Checking warning sticker.  
4.68  
Water drain valves at rear (Passat es‐  
tate): check for blockages, clean if nec‐  
essary  
– Detach wheel housing liner at rear left -1- sufficiently to gain  
access to water drain valve -2-.  
– Open rear water drain valve, check it for damage, and re‐  
move any blockages.  
– Repeat procedure on other side of vehicle.  
4.69  
Toothed belt (petrol engines): renewing  
Camshaft drive toothed belt: renewing, petrol engines  
– ⇒ 4-cylinder injection engine (1.4 l direct injection engine,  
turbocharger); Rep. gr. 15; Toothed belt drive; Removing  
and installing toothed belt  
Coolant pump toothed belt: renewing, petrol engines  
– ⇒ 4-cyl. injection engine (1.4 l direct injection engine, turbo‐  
charger); Rep. gr. 19; Coolant pump/thermostat assembly  
4.70  
Camshaft drive toothed belt (diesel en‐  
gines): renewing  
TDI common rail engines:  
– ⇒ Rep. gr. 15; Toothed belt drive; Removing and installing  
toothed belt  
4. Descriptions of work  
191  

Need help?

If after viewing the owner's manual or service manual you still have some unresolved questions about the car VW Passat you can write to us using the link below, describing your problem in detail, we try to answer all questions.


Ask your question on the page - Support!