CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018
13 – Crankshaft group
1
Cylinder block (pulley end)
Removing and installing poly V-belt ⇒ page 39
Removing and installing tensioner for poly V-belt (Passat 2006 ▶,
CC) ⇒ page 40 .
Removing and installing tensioner for poly V-belt (Golf, Eos, Scir‐
occo) ⇒ page 43 .
Removing and installing tensioner for poly V-belt (Tiguan)
⇒ page 47 .
Removing and installing bracket for ancillary units ⇒ page 50 .
Removing and installing vibration damper ⇒ page 51
Renewing oil seal for vibration damper ⇒ page 58 .
1.1
Assembly overview - poly V-belt drive
1 - Vibration damper
❑ With poly V-belt pulley
❑ Removing and installing
⇒ page 51
2 - O-ring
❑ Renew
3 - Bolt
❑ Renew
❑ Removing and installing
⇒ page 51
1
❑
150 Nm + 90° ( / turn)
4
further
❑ Use counterhold -
T10355- when loosen‐
ing and tightening
4 - Poly V-belt
❑ Check for wear
❑ Do not kink
Caution
Danger of destruction
due to reverse running
direction in the case of a
poly V-belt that has al‐
ready run.
B♦efore removing the poly
V-belt, use a piece of
chalk or a felt pen to mark
the running direction.
❑ Removing and installing
⇒ page 39
❑ When installing, make
sure it is properly seated on pulleys.
1. Cylinder block (pulley end)
37
CC 2010 ➤ , Eos 2006 ➤ , Golf 2004 ➤ , Golf 2009 ➤ , Passat 2006 ➤ , ...
4-cyl. injection engine (1.8 and 2.0 l engine, chain drive) - Edition 08.2018
5 - Tensioning device for poly V-belt
❑ Swing with open-end spanner to slacken poly V-belt.
❑ Lock with locking pin - T10060 A- .
❑ Removing and installing (Passat, CC) ⇒ page 40
❑ Removing and installing (Golf, Eos, Scirocco) ⇒ page 43
❑ Removing and installing (Tiguan) ⇒ page 47
6 - Ancillary bracket
❑ With oil pressure switch - F1- , oil filter and engine oil cooler
❑ Removing and installing ancillary bracket ⇒ page 50 .
❑ Removing and installing engine oil cooler ⇒ page 226
7 - Bolt
❑ 10 Nm
8 - Alternator
❑ Removing and installing ⇒ Rep. gr. 27
9 - Bolt
❑ 23 Nm
10 - Bolt
❑ Tightening sequence ⇒ page 39
11 - Air conditioner compressor
❑ Do not unscrew or disconnect refrigerant lines
❑ Removing and installing ⇒ Rep. gr. 87
12 - Bolt
❑ 25 Nm
13 - Dowel sleeve
❑ For air conditioner compressor.
Components of tensioner for poly V-belt
1 - Tensioning roller, tighten securing bolt to 60 Nm
2 - Support element
3 - Ancillary bracket
4 - Centring sleeve
5 - Bolt
38
Rep. gr.13 - Crankshaft group
2024 VW Passat Owner's Manual
VW Passat B7 Service & Repair Manual
VW Passat B6 Service & Repair Manual
